iFlight Chimera7 320mm 7inch 6S FPV LR Analog BNF with Caddx Ratel camera /Xing 2806.5 1300KV/1800KV Motor for FPV Long Range

SKU: PMSB5D5QG013 Category: Tag:


No RX 1300KV Cruiser
No RX 1300KV Cruiser
No RX SpeedCruiser
No RX SpeedCruiser
TBS 1300KV Cruiser
TBS 1300KV Cruiser
TBS 1800SpeedCruiser
TBS 1800SpeedCruiser

Product Description


  • Introducing what has been requested for too long already! A super efficient iFlight 7inch Long-Range bird that can go where you couldn’t go before and can carry bigger batteries to get the flight time to surf the swiss alps if you want! Super stiff frame for minimum resonance and 2806.5 motors for maximum 7inch prop control. Fly big batteries top-mounted, or even bigger batteries bottom-mounted, 6cells recommended or 5cells for slow cruising. But whatever style you fly, a Lipo or Lion pack will just do the job. Recommended 5S 3.000mAh above (slow cruising) or 6S 2.500mAh above.

  • GPS functionality to find your way back and Betaflight GPS Rescue mode ready to setup (default OFF to prevent unexpected behaviour; Setup instructions included). Vertical and horizontal TBS Crossfire antenna mounts included to cover you and your antenna dead ends just in case. GoPro universal TPU bottom stand included; fits your original GoPro bracket and our TPU GoPro protectors (additional).


  • VTX is set to 25mW by default! Power levels above 25mW require a HAM license or have to be approved by local authorities! Please ensure you’re flying legal frequencies and use our prepared Betaflight VTX tables according to your region.


  • 6mm rigid arm design for more stiffness

  • Top- and bottom battery mount option

  • XING 2806.5 efficient wide stator motors

  • GPS pre-installed for more safety at distance

  • 800mW high power adjustable VTX

  • GoPro TPU bottom stand (GoPro protector not included)

  • 360°?TPU protection, FPV cam protection and antenna mounts

  • Battery voltage LED status light (illuminated IF logo on the bottom)


  • Is this your first BNF or are you just starting through with FPV? This article might probably help:

  • Don’t worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!

  • To restore lost tunes or updates, please check our linked article on

  • Angle-Mode (self balancing level mode) is enabled by default to make sure your first flight doesn’t end in a mess!

  • Please check our linked article on

  • GPS Rescue is OFF by default to prevent from unwanted or unexpected drone behaviour.

  • Please check our linked article on

FRAME //:?Chimera7

  • Wheelbase: 320mm

  • Main body dimension: 258*199mm

  • Bottom to top distance: 20mm

  • Arm thickness: 6mm

  • Bottom plate thickness: 3mm

  • Top plate thickness: 2mm

  • Upper(middle) plate thickness: 3mm

  • Camera plate thickness: 3mm (included TPU inserts)

ELECTRONICS // SucceX-D F7 V2.1 Stack (50A 4-in-1 ESC):

SucceX-D F7 V2.1 TwinG

  • MCU: 216MHz STM32F722

  • Gyro:2x ICM20689

  • Baro: YES

  • Blackbox:32MB

  • Betaflight OSD: YES

  • BEC: 5V 2.5A / 9V 2.5A

  • Current sensor scale: ?100

  • Inverter for SBUS input (UART2-RX)

  • Smartaudio & Tramp VTX protocol supported

  • Beeper pad : Yes

  • RSSI input pad: No

  • UARTs:5

  • Motor outputs: 8

  • 8 pin 4in1 ESC port (GND, VBAT, M1, M2, M3, M4, CUR, R5)

  • BLHeli32 Telemetry:RX5

  • Input voltage:recommended 2-6S, MAX 8S

  • Firmware Target:? ?IFLIGHT_F722_TWING

  • Mounting pattern: 30.5*30.5mm φ4mm with Grommets?φ3mm

  • Dimensions: ? 36*36mm

  • Weight: 7.5g

  • USB type-C

ESC // SucceX 50A

  • MCU:?STM32F051

  • Up tp 48kHz PWM frequency

  • Capacitance: 470uF/50V

  • Current Sensor: Yes

  • Input: 2-6S LIPO

  • Constant: 50A / Burst: 60A

  • BlHeli32 telemetry: Yes

  • BEC: No

  • Supports up to Dshot1200, Proshot, Oneshot, Multishot

  • Target: iFlight-BL32-4IN1

  • Weight:?14.4g

  • Mounting pattern:?30.5*30.5mm/Φ3mm

  • Dimensions:?43*39mm (including the power pads)

VTX// SucceX Force 5.8g 800mW VTX Adjustable

  • Item: SucceX-Force 800mW adjustable VTX

  • Input voltage: 5V

  • Output voltage/ Max current: 5V 1A

  • 12V input current: 40mA@PIT MODE, 95mA@25mW, 185mA@200mW,250mA@500mW, 380mA@800mW

  • Channel: 48

  • size:36*36*3mm

  • PIT/25mW/200mW/400mW/800mW

BNF // Parts list (Build)

  • Prebuilt and indoor tested Quadcopter

  • 1x?Chimera7 frame

  • 1x GoPro TPU bottom stand incl. lock screw

  • 1x?Caddx Ratel, 2.1mm lens camera

  • 1x?Albatross RHCP?SMA?5.8g 150mm antenna

  • 2 sets x Gemfan tri-blade 7040 props (Set of 4 – Color may vary)

  • 4x?20*250mm?Microfiber PU Leather Battery Strap (Color May Vary)

Additional Suggested Parts (not included)

  • Adjustable Gopro mount(0-40)




Carbon Fiber

Recommend Age


Tool Supplies


Upgrade Parts/Accessories


RC Parts & Accs



320mm 7inch


Vehicles & Remote Control Toys



Technical parameters

Value 2

Model Number


Remote Control Peripherals/Devices

Remote Controller

For Vehicle Type


Four-wheel Drive Attributes



Bottom Plate

There are no reviews yet.

Be the first to review “iFlight Chimera7 320mm 7inch 6S FPV LR Analog BNF with Caddx Ratel camera /Xing 2806.5 1300KV/1800KV Motor for FPV Long Range”