Note: Protek25 BNF is available in black and green color, please leave a message if you need green, otherwise we will ship black by default，thanks！
Our all new 2.5inch project is finally ready for all you content creators or those guys who like to wear some protection every now and then. Prop protection is what we’re talking about here…
ProTek is not necessarily just a Cinewhoop series but far more. Equipped with our popular XING 1404 motors in a higher kv class will give you all the power you need to get good speed, do some freestyle or carry a full GoPro through tiny gaps.
A lot of thought was put into the different assembly options. Our stock BNF will ship in the standard configuration but you can either do a pusher mod (flip the build upside down) or a lite mod (remove the protective plastic for weight optimization).
Durable plastic protectors with copper standoffs, portable compact design, easy accessable UBS port without disassembly, LED battery status, lost model buzzer and a universal GoPro TPU for a full size or naked GoPro. If you wanna go extra light, get one of our 5V balance plug GoPro power cables to get rid of the internal battery.
Need a naked GoPro case or mount? Checkout our new iFlight naked GoPro Hero8 TPU case to use with your ProTek25.
R81-SPI Frsky (Compatible W/ Frsky ACCST D8）
No Props or frame in view!
Caddx.us Turbo Eos V2 FPVCam?2.1mm 16:9 NTSC
High performance?SucceX-D 20A Whoop F4 AIO Board?to save weight and space
T700 Quality Carbon (40% more tensile strength compared to common 3K carbon)
Lightweight one-piece frame design (Less flexibility, more Rigid, more Durable)
Low Resonance frame construction (Less Jello, more Cinematic footage)
Butter smooth XING?1404 5500KV?motors
Pre-tuned with smooth freestyle settings
PRE-TUNED & PRE-SETUP:
Don’t worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!
To restore lost tunes or updates, please check our linked article on
Angle-Mode (self balancing level mode) is enabled by default to make sure your first flight doesn’t end in a mess!
Please check our linked article on
ProTek25 BNF Specs:
SucceX-D 20A Whoop AIO
Motor: XING 1404?5500KV
Body Size: 91*68.7mm
Bottom plate thickness: 3mm
Top plate thickness: 2mm
Top and bottom plate spacing:?24mm?(aluminum standoff height)
Propeller size: 2.5 inch
FC pattern:?25.5*25.5mm / 20*20mmmm
FPV cam spacing: 20mm
Weight: 194.3g (without battery)
ProTek25?Quad BNF Included Components and Parts
pre-built and tested Quadcopter
1x ProTek25 Frame
1x?Caddx.us Turbo Eos V2 FPVCam?2.1mm 16:9 NTSC
1x?Albatross LHCP?RP-SMA?5.8g antenna
2x Nazgul 2525 propeller (Set of 4 – Color May Vary)
2x iFlight Lipo Strap 15*200mm (Color May Vary)
1x NakedGoPro TPU bottom stand black (Naked GoPro Protector not included)
FC // SucceX-D 20A F4 Whoop AIO
BEC output：5V 2A/10V 2A
INA pad：UART2 (nR2)
ESC Firmware：G-H-30 BLS
VTX// SucceX Micro Force 5.8GHz 300mW VTX Adjustable
Antenna interface: IPEX (UFL)
VTX protocol : IRC Tramp
Additional Suggested Parts
- iFlight FPV Goggles with DVR Function
Battery 4S 850mAh
The camera mount TPU donot include.
|RC Parts & Accs|
Vehicles & Remote Control Toys
|Remote Control Peripherals/Devices|
|For Vehicle Type|
|Four-wheel Drive Attributes|