Newest Betafpv BEC Board for Naked Camera GoPro HERO6 HERO7 and GoPro HERO8 2-4S Input Voltage RC DIY FPV Racing Drone

SKU: VBWMDHGJIO3S Category: Tag:

$10.99

Clear
Compare

Product Description

You asked, we listen! To provide more choice for our customers, not only the BEC board for HERO6/7, BETAFPV also designed a new BEC board for GoPro HERO8. You don’t need to worry your GoPro will turn off during a flight anymore. This BEC board only weighs about 1.5g, which makes your naked GoPro super neat and light. This BEC Board has integrated [email protected] BEC, stock GoPro buttons, and LED pluggable connectors and remote recording!

Noticed: The BEC board for HERO8 does not fit the Case V2.

Bullet point
BEC Board is specially designed for Naked GoPro HERO6/7/8 which weighs about 1.5g, makes your naked GoPro lighter and easy to install on your drone.
The BEC output voltage is [email protected], avoid the accident of power of which is caused by the insufficient power supply for the FC board. Also, stock buttons and LEDs are integrated.
Integrated GoPro stock buttons, Power/Mode Button and Record Button.
Integrated GoPro stock LED to know the status of the camera.
The pad is available for pilots to control the GoPro recording via the radio transmitter.
With the pluggable connector, which is easier to connect with your flight controller for power supply and recording.

Specification
Item: BEC Board for Naked Camera
Weight: 1.53g/1.57g
Output: 5V @ 2A
Input voltage: 2-4S
Connector: GH 1.25 3P connector

Diagram of BEC Board
The two buttons on the BEC board has the same function as the stock GoPro buttons. Three actions we will use frequently.

Power On – Press the Power/Mode button and the LED flashes three times and light off.
Start Record – Press the Record button once and LED flashes slowly. If LED flash once and light off, it means there is no SD card.
Stop Record – Press the Record button and LED stop slow flashing.

BEC Board for GoPro HERO8

 

LED Status
Under normal operation, plug the GH1.25 connector into the naked camera firstly, then connect with the battery. The LED will flash once, then you should press the Power/Mode button once in a second to power on. The LED on the BEC board has the same status as the stock LED on the GoPro mainboard.

How to Setup Remote Record
Pilot could use the switch on radio transmitter to start/stop record. Some more configuration needed.

For example, if you use F4 FC V2.0 in the drone, like the 95X whoop drone, the connection diagram is shown below. The yellow cable (FC B12 pin pad) is just for the remote record.

We use the Pinio function in Betaflight to control record. First, setup the Pinio function of the B12 pin in the FC board.

resource FLASH_CS 1 NONE
resource PINIO 1 B12
set pinio_box = 40,255,255,255
save

Next, map one of the switch channels in your radio transmitter to this Pinio (aka USER1). As shown below, we map the AUX4 channel in the radio transmitter to USER1 Pinio. The cursor in the orange zone means button released and white zone means pressed. So keep the cursor in the orange zone in default.

Third, check if the Pinio function works. Change the switch and make the cursor move from the orange zone to the white zone, and finally back to the orange zone. Now you could check the LED status to know if the record starts. Use the same process to stop recording.

If you use the 12A F4 AIO FCboard, like the 85X whoop drone, you will use the LED_STRIP pin (aka A08 pin pad) for the Pinio function.

resource LED_STRIP 1 NONE
resource PINIO 1 A08
set pinio_box = 40,255,255,255
save

Note: Do this at your own risk. You will lose your GoPro’s warranty and you may end up bricking the camera if something goes wrong. This guide is not authorized by GoPro and your camera is not guaranteed to work afterward. BETAFPV will not be held responsible for this action.

How to assemble the BEC Board on Naked Camera.

Package
1 * BEC Board for Naked Camera
1 * H1.25 Power Cable (80mm 30AWG)

or

1 * BEC Board for GoPro HERO8
1 * GH1.25 Power Cable (80mm 30AWG)
3 * M1.4*4 Screws


 

Brand Name

uuustore

Origin

CN(Origin)

Material

Composite Material

Recommend Age

12+y

Tool Supplies

Assembled class

Upgrade Parts/Accessories

Frame

RC Parts & Accs

Radio Systems

Use

Vehicles & Remote Control Toys

Model Number

Betafpv BEC Board

Remote Control Peripherals/Devices

Remote Controller

Four-wheel Drive Attributes

Assemblage

There are no reviews yet.

Be the first to review “Newest Betafpv BEC Board for Naked Camera GoPro HERO6 HERO7 and GoPro HERO8 2-4S Input Voltage RC DIY FPV Racing Drone”